# 启动
```cmd
python run_defect_score_server.py
```

## 中文对照
```json
{
  "face": "面",
  "wear": "磨损",
  "scratch": "划痕",
  "stain": "污渍",
  "scuff": "磨痕",
  "impact": "撞击痕迹",
  "damaged": "损坏",
  "wear_and_impact": "磨损和撞击痕迹",
  "pit": "凹坑",
  "corner": "角",
  "wear_and_stain": "磨损和污渍",
  "inner_box": "内框",
  "outer_box": "外框"
}
```

### 缺陷类型
```text
面缺陷: "1": "wear", "2": "scratch", "3": "stain",
        "4": "scuff", "5": "impact", "6": "damaged",
        "7": "wear_and_impact", "8": "pit"
    
边角缺陷: "1": "wear", "2": "wear_and_impact", "3": "damaged",
         "4": "impact", "5": "wear_and_stain"

```

### 缺陷划分
```text
边角
wear_area: 'wear', 'wear_and_impact', 'wear_and_stain'
loss_area: 'impact', 'damaged'

面
wear_area: 'wear', 'wear_and_impact', 'damaged'
scratch_length: 'scratch', 'scuff'
pit_area: 'pit', 'impact'
stain_area: 'stain'
```

## 分数配置信息备注
```text
base_score: 基础分数

corner: 角
    rule: 分数规则
        wear_area:"磨损的扣分规则"
        loss_area: "缺失的扣分规则"
    front_weights: "正面的权重分配"
        wear_area:"-权重"
        loss_area:"-权重"
    back_weights: "背面的权重分配"
        ...
        ...
    final_weights: "最终权重分配"
        front: "正面权重"
        back: "背面权重"

edge: 边
    ...与 corner 类似
    
face: 面
    rule: 分数规则
        wear_area: 磨损
        pit_area: 凹坑
        stain_area: 污渍
        scratch_length: 划痕长度(!注意只有它看长度, 其他的看面积)
    coefficients: 权重分配
        ...这里是几种缺陷对应的权重
    final_weights: "最终权重分配"
        ...

centering: 居中
    front: 正面
        rules: 规则
    coefficients: 权重分配
        horizontal: 水平
        vertical: 上下
    back: 背面
        ...
    final_weights: "最终权重分配"
        ...

card: 卡片
    PSA: 卡的类型, 默认用它
        ...不同类型的权重最后分配
```

### 分数规则要求

规则为: min<=缺陷面积<max , 扣 deduction 的分数

要求
1. 第一个 min 必须为 0
2. 除第一个min, 所有min必须等于上一个的max
3. 最后一个的max必须为 "inf", 即无穷大
```
"wear_area": [
        {
          "min": 0, 
          "max": 0.05,
          "deduction": -0.1
        },
        {
          "min": 0.05,
          "max": 0.1,
          "deduction": -0.5
        },
        {
          "min": 0.1,
          "max": 0.25,
          "deduction": -1.5
        },
        {
          "min": 0.25,
          "max": 0.5,
          "deduction": -3
        },
        {
          "min": 0.5,
          "max": "inf",
          "deduction": -5
        }
```